Osburn OB01801 Bedienungsanleitung Seite 1

READ AND KEEP THIS MANUAL FOR REFERENCE 45058A Printed in Canada 12-06-2015 OWNER`S MANUAL 1800 INSERT (OB01801 model) US ENVIRONMENTAL PROT

/10 2.6 Positioning the unit In addition to ensuring compliance of the masonry fireplace hearth extension (see Compliance of the masonry fireplace i

/11If a non-combustible material floor protection needs to be added in front and level with the hearth extension masonry fireplace (s

/12The use of an R value is convenient when more than one material is going to be used in the hearth extension to cover the combustible surfa

/13Thermal characteristics of common floor protection materials* MATERIAL CONDUCTIVITY (k) PER INCH RESISTANCE (R) PER INCH THICKNESS Micore® 160

/14 MINIMUM MASONRY OPENING J 20" (508 mm) K 23 3/8" (594 mm) L 14 5/8" (371 mm) CLEARANCES F 17" (432 mm) G 10" (254

/152.8 Connector installation A masonry flue connector may provide acceptable performance (Figure 2.8a); however, we recommend the use of a chimney

/162.8.1 Chimney liner installation To install of the chimney liner, the preferred methods are those found in Section 2.8.1.1. Use a liner offset ad

/172.8.1.2 If the chimney liner does not align with the insert’s flue outlet: You can get a liner offset adapter (AC01370), sold separately. If you

/182.9 Air control plate, faceplate and fan Assembly Instructions 1. Place the faceplate panels with the finished side down on a flat, soft, non-ab

/19 Figure 2.9c Figure 2.9d Figure 2.9e 7. Fan is already attached to the unit at the factory with two tie str

/2INTRODUCTION SBI INC., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on your purchase

/208. Cooktop is installed at the factory. Shipping screw must be removed before installation of faceplates. (Figure 2..9f) 9. Install faceplate (

/21Section 3.0 Operation 3.1 Safety Information 1. This insert is designed for safe operation WHEN BURNING CORDWOOD ONLY. Altering or

/2210. Never operate the insert with the door open, or cracked slightly open, except briefly during the lighting operation, and during refuelling. L

/23Common Heating Values of Cordwood Hardwoods Million Btu/Cord Softwoods Million Btu/Cord Birch 23.6 Douglas Fir 20.6 White Oak 28.3 Hemloc

/24the door. 6. Ideally the large kindling should be burned until a thick bed of red embers is obtained. At that point, add cordwood fuel and conti

/253.5 Maintaining The Fire Your Osburn insert will work best if a thick bed of hot embers is maintained in the bottom of the firebox, and a minimum

/263.6 Fan Operation 1. Allow the insert to reach operating temperature (approximately one hour), before turning on the fan, since increased ai

/27Section 4.0 Maintenance 4.1 Care And Cleaning Clean the insert frequently so that soot, ash and creosote do not accumulate. Do not attempt to

/28CAUTION: OPERATION OF YOUR OSBURN 1800 WITHOUT THE BAFFLE MAY CAUSE UNSAFE AND HAZARDOUS TEMPERATURE CONDITIONS AND WILL VOID THE WARRANTY. Conta

/294.4 Baffle Installation and Brick Notes: 1. Stack the baffle boards (A) on top of the vermiculite boards (B) as shown in figure 4.4a . Figure 4

/3TABLE OF CONTENTS INTRODUCTION...

/303. Install the baffle support/extension (H) ensuring that it fits between the front risers and hold it in place. Install the front secondary air

/31All firebrick and duraboard baffles must be properly in place for correct burning operation. Have any damaged firebricks replaced. Check the fireb

/324.5 Secondary Air Tube Replacement (see Figure 4.5) 1. Remove cotter pin at LH end of tube. 2. Slide tube to right and lower tube end below LH p

/334.6 Fan Maintenance & Care Clean the fan air inlet louvres and squirrel cage impeller regularly. The fan should be kept clean and dust free.

/34Section 5.0 Troubleshooting Symptom Possible Cause Corrective Action I Smoke in room 1. Down draft 1. Upgrade chimney 2. Chim

/35Section 6.0 Specifications Fuel Type Dry cordwood Test Standards ULC S628 (CSA B366.2) & UL 1482 residential. Maximum re

/36OSBURN LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original retail purchaser and is not transfe

/4OUTSIDE DIMENSIONS

/5Section 1.0 Pre-Installation Requirements This unit is designed for safe operation. Altering or modifying the unit, or installation, without p

/66. OPENING SIZE: Refer to “Suitable Fireplace Dimensions” for suitable size fireplace openings. NOTE: A METAL TAG IS PROVIDED AN

/7Section 2.0 Installation 2.1 Safety information NOTE: THIS APPLIANCE IS NOT RECOMMENDED FOR USE IN A HOME IF AN OCCUPANT HAS ANY RESPIRATORY OR

/82.2 Installation instructions Inspect the masonry fireplace according to the safety information and fireplace requirements and have it cleaned and

/92.4 The masonry fireplace's draft control system If the fireplace's draft control system is to remain in the masonry fireplace, it must