Osburn OB01111 Bedienungsanleitung

READ AND KEEP THIS MANUAL FOR REFERENCE 45127A Printed in Canada 12-06-2015 OWNER`S MANUAL 1100 (OB01111 model) US ENVIRONMENTAL PROTECTION AGEN

10 FIGURE 1.3 Clearances to combustible materials and floor protection

11 Floor protector If the stove is to be installed on top of a combustible floor, it must be guarded by a non combustible materi

12 TYPE OF PROTECTION Reducing Clearances With Shielding Sides and Rear/Back Top Sheet metal, a minimum of 0,024" (0,61mm) spaced out at least

13 Graphic 1 A- Minimum clearance required between the appliance and an unshielded combustible ceiling. B- 20 in. (500 mm) minimum; C- 1 in.

14 Graphic 2 A- 1 in.(25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- 0.024’’ (0.61mm) sheet metal. Graphic 3 A- 1 in. (2

15 Graphic 5 A- 1 in. (25 mm) minimum; 1- Combustible wall; 2- Non-combustible spacers; 3- Brick. Graphique 6 A- 1 in. (25 mm) minimum; 1-

16 CHIMNEY SYSTEM DEFINITIONS For clarity, the following definitions should be used with respect to these instructions: A chimney system consists

17 RESIDENTIAL CLOSE CLEARANCES CHIMNEY SYSTEM In addition to the requirements of section 1.6.2.1 the following components are required

• The connector must not pass through any combustible material, nor may it pass through a concealed space (such as an attic, roof space,

19 • The assembly should be as short and direct as possible between the stove and chimney (See figure 2.4 (A)). The use of two 45 degr

2 INTRODUCTION SBI INC., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on your purchas

20 Figure 1.6 – Chimney height EXTERIOR CHIMNEY Chimneys constructed outside of the home on an exterior wall should be avoided if possible, espec

21 TYPICAL TYPES OF CHIMNEY SYSTEMS There are basically two types of chimney systems; one employs an existing masonry chimney, while th

22 Figure 1.8 Connections to a Factory Built Chimney (Interior Shown) Figure 1.9 Connection to a Factory Built Chimney (Exterior Shown)

23 OPERATION SAFETY INFORMATION 1. This stove is designed for safe operation WHEN BURNING CORDWOOD ONLY. Altering or modifying the unit o

24 10. Never operate the stove with the door open, or cracked slightly open, except briefly during the lighting operation, and during refuelli

25 SIMPLE WOOD MOISTURE TEST Add one large piece of wood to the top of an established fire. If it starts to burn on three sides. Within one minute

26 Open the draft control (located on the front of the stove) fully by moving it from the left to the right, as shown in Figure 2.1 and as indicated

27 MAINTAINING THE FIRE Your Osburn stove will work best if a thick bed of hot embers is maintained in the bottom of the firebox, a

28 (OPTIONAL) BLOWER INSTALLATION AND OPERATION 1. Allow the stove to reach operating temperature (approximately one hour), before turn

29 MAINTENANCE CARE AND CLEANING Clean the stove frequently so that soot, ash and creosote do not accumulate. Do not attempt to clean the stove,

3 TABLE OF CONTENTS INTRODUCTION ...

30 4. Clear the ashes from the area where the plug normally sits so that it will properly seat against the opening edges; tap it down with

31 CHIMNEY CLEANING Regular chimney maintenance, as well as good burning practices, are required to prevent chimney fires. The chi

32 BAFFLE INSTALLATION AND BRICK NOTES Follow these instructions to remove the baffle: 1. Lift the front bricks over the front of baffle support

33 BRICK LAYOUT Figure 3.3 SECONDARY AIR TUBE REPLACEMENT (See Figure 3.4) 1. Remove cotter pin at LH end of tube. 2. Slide tube to right

34 TROUBLESHOOTING Symptom Possible Cause Corrective Action I Smoke in room 1. Down draft 1. Upgrade chimney 2. Chimney blocked

35 SPECIFICATIONS FUEL TYPE Dry cordwood TEST STANDARDS 1. ULC S627 (CSA B366.2) & UL 1482 residential and mobile home.

36 OSBURN LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original retail purchaser and is not transferable. This w

4 OVERALL STOVE DIMENSIONS Figure 1

5 INSTALLATION REQUIREMENTS In Canada the CSA B365 Installation Code for Solid Fuel Burning Appliances and Equipment and the CSA C22.1 Canadian Na

6 MANUFACTURED (MOBILE) HOME INSTALLATIONS – ADDITIONAL REQUIREMENTS 1. The stove must be bolted to the floor (secure the unit by prying out the t

7 INSTALLATION When installed and operated as described in these instructions, the Osburn 1100 wood stove is suitable for use as a freestan

8 DOOR OVERLAY INSTALLATION In order to complete the assembly of your freestanding Osburn 1100 wood stove, you need to install the door overlay. Se

9 CLEARANCES TO COMBUSTIBLES AND FLOOR PROTECTOR To install your appliance correctly, it is extremely important to respect all clearances to any co